best baby monitor dual receiver image
kitty98
This house is already pre-wired: it has in-ceiling speakers in the master bedroom, bathroom, garage, and patio (these are 80W). Every set of speakers has its own volume control. Plus there are also 6 speaker hook ups in the living room.
I want to set up capable of playing different things at the same time, ie. if I want to hear music in my bedroom, while my roommate watches a movie in the living room. How can I do this? what good receiver can handle this? I need a receiver capable of handling 2 or more different sources at the same time.
I also need a surround sound sys for the living room. It has the cables, but not the speakers. Recomendations?
Do I need an amplifier too, or the receiver alone can deal w this?
I'm pretty new w all this, so info w baby steps will be greatly appreciated :-)
Answer
I have provided links below with tutorials and diagrams for multi room applications. You will need a receiver with dual zone capabilities. You do not say if your volume controls have impedance matching. If they are impedance matching controls you will only need to add a fairly beefy two channel amp (which you will connect to your receiver's zone two preamp outputs) to drive the speakers in the bedroom, bathroom, garage, and patio. If these volume controls do not do impedance matching I recommend you get a multi channel amplifier (you will need at least eight channels) which you will connect to the zone two preamp outputs. This will give you MUCH better performance in your bedroom, bathroom, garage, and patio than trying to drive all 4 pairs of speakers by your receiver's zone 2 output (low power). You do not need a speaker selector (switch) since you have volume controls unless you want to use this for impedance matching. I would not recommend it for that purpose though (signal loss). Either go with an impedance matching block or (BETTER) go with the multi channel amp. Since volume controls usually don't provide much information on the front and since you are pretty new to this you may need to find out who installed the system to find out if these controllers are impedance matching. Worst case scenario an installer can look at the back of the controllers to tell you if they are impedance matching. People who do multi-room on the cheap usually go back eventually to upgrade their system. Best to do it right to begin with.
Recommendations for your home theater:
1) Do a lot of comparison listening and pick what sounds best to you.
2) Be sure to listen to brands such as M&K (I like these alot), Monitor Audio, and B&W on the higher end. On the slightly lower end try brands such as Boston Acoustics, Klipsch, and Paradigm.
3) Recievers: I like Denon (sound quality). Onkyo, Yamaha, and Harmon Kardon are good too.
I have provided links below with tutorials and diagrams for multi room applications. You will need a receiver with dual zone capabilities. You do not say if your volume controls have impedance matching. If they are impedance matching controls you will only need to add a fairly beefy two channel amp (which you will connect to your receiver's zone two preamp outputs) to drive the speakers in the bedroom, bathroom, garage, and patio. If these volume controls do not do impedance matching I recommend you get a multi channel amplifier (you will need at least eight channels) which you will connect to the zone two preamp outputs. This will give you MUCH better performance in your bedroom, bathroom, garage, and patio than trying to drive all 4 pairs of speakers by your receiver's zone 2 output (low power). You do not need a speaker selector (switch) since you have volume controls unless you want to use this for impedance matching. I would not recommend it for that purpose though (signal loss). Either go with an impedance matching block or (BETTER) go with the multi channel amp. Since volume controls usually don't provide much information on the front and since you are pretty new to this you may need to find out who installed the system to find out if these controllers are impedance matching. Worst case scenario an installer can look at the back of the controllers to tell you if they are impedance matching. People who do multi-room on the cheap usually go back eventually to upgrade their system. Best to do it right to begin with.
Recommendations for your home theater:
1) Do a lot of comparison listening and pick what sounds best to you.
2) Be sure to listen to brands such as M&K (I like these alot), Monitor Audio, and B&W on the higher end. On the slightly lower end try brands such as Boston Acoustics, Klipsch, and Paradigm.
3) Recievers: I like Denon (sound quality). Onkyo, Yamaha, and Harmon Kardon are good too.
Is there anyway to boost my reception in my basement?
rynearson9
I get decent signal on the main floor and when i go in the basement my signal sucks. I have Verizon
Answer
Well here is some information that tells you what interferes with wireless signal:
Sources of interference for wireless devices and networks
The farther away the interference source, the less likely it is to cause an issue. The following items can cause interference with wireless communication:
* Microwave ovens: Placing your computer, Bluetooth wireless device, or AirPort base station near a microwave oven that is in use may cause interference.
* Direct Satellite Service (DSS) RF leakage: The coax cable that comes with certain types of satellite dishes may cause interference. Obtain newer cables if you suspect RF leakage.
* Certain electrical devices such as power lines, electrical railroad tracks, and power stations.
* 2.4 GHz or 5 GHz phones: A cordless telephone that operates in this range may cause interference with wireless devices or networks when used.
* Metal objects: If possible, move metal objects or change the placement of the computer, wireless device or wireless access point so the path between your computer and the wireless device or wireless access point is free from metal objects that may cause interference.
* Video senders (transmitters/receivers) that operate in the 2.4 GHz or 5 GHz bandwidth.
* Wireless speakers that operate in the 2.4 GHz or 5 GHz bandwidth.
* Certain external monitors and LCD displays: Certain displays may emit harmonic interference, especially in the 2.4GHz bandwidth between channels 11 and 14. This interference may be at its worst if you have a portable computer with the lid closed and an external monitor connected to it. Try changing your access point to use 5 Ghz or a lower 2.4 GHz channel.
* Any other "wireless" devices that operate in the 2.4 GHz or 5 GHz bandwidth (microwaves, cameras, baby monitors, and so on).
Note: Some devices may not overtly state that they operate in the 2.4 GHz or 5 GHz bandwidth. The operations manual should indicate the frequencies the device uses to operate. These may be referred to as "Dual Band" or "Wireless" devices.
Effect of home and office elements on wireless communication
Where you are located and what materials you are surrounded by can affect your wireless networking performance or Bluetooth wireless device. The table below shows common elements and their potential for interference.
Type of Barrier Interference Potential
Wood Low Interference
Plaster Low Interference
Synthetic material Low Interference
Glass Low Interference
Water Medium Interference
Bricks Medium Interference
Marble Medium Interference
Paper rolls High Interference
Concrete High Interference
Bulletproof glass High Interference
Metal Very high Interference
I would say your problem is Concrete because of the bricks, which are almost the hardest next to metal and bulletproof glass... But if you can get a wireless access point and get it at the entrance of the basement, it will take the signal from your router and extend it into your basement. You can take these WAPoints and move them around to see where you get the best signal in your basement with where the access point extends the signal too. I hope this helps. Also some of the other items listed above can cause inteference but I would suspect the concrete and start there. There not too expensive and you can have more than one.
Well here is some information that tells you what interferes with wireless signal:
Sources of interference for wireless devices and networks
The farther away the interference source, the less likely it is to cause an issue. The following items can cause interference with wireless communication:
* Microwave ovens: Placing your computer, Bluetooth wireless device, or AirPort base station near a microwave oven that is in use may cause interference.
* Direct Satellite Service (DSS) RF leakage: The coax cable that comes with certain types of satellite dishes may cause interference. Obtain newer cables if you suspect RF leakage.
* Certain electrical devices such as power lines, electrical railroad tracks, and power stations.
* 2.4 GHz or 5 GHz phones: A cordless telephone that operates in this range may cause interference with wireless devices or networks when used.
* Metal objects: If possible, move metal objects or change the placement of the computer, wireless device or wireless access point so the path between your computer and the wireless device or wireless access point is free from metal objects that may cause interference.
* Video senders (transmitters/receivers) that operate in the 2.4 GHz or 5 GHz bandwidth.
* Wireless speakers that operate in the 2.4 GHz or 5 GHz bandwidth.
* Certain external monitors and LCD displays: Certain displays may emit harmonic interference, especially in the 2.4GHz bandwidth between channels 11 and 14. This interference may be at its worst if you have a portable computer with the lid closed and an external monitor connected to it. Try changing your access point to use 5 Ghz or a lower 2.4 GHz channel.
* Any other "wireless" devices that operate in the 2.4 GHz or 5 GHz bandwidth (microwaves, cameras, baby monitors, and so on).
Note: Some devices may not overtly state that they operate in the 2.4 GHz or 5 GHz bandwidth. The operations manual should indicate the frequencies the device uses to operate. These may be referred to as "Dual Band" or "Wireless" devices.
Effect of home and office elements on wireless communication
Where you are located and what materials you are surrounded by can affect your wireless networking performance or Bluetooth wireless device. The table below shows common elements and their potential for interference.
Type of Barrier Interference Potential
Wood Low Interference
Plaster Low Interference
Synthetic material Low Interference
Glass Low Interference
Water Medium Interference
Bricks Medium Interference
Marble Medium Interference
Paper rolls High Interference
Concrete High Interference
Bulletproof glass High Interference
Metal Very high Interference
I would say your problem is Concrete because of the bricks, which are almost the hardest next to metal and bulletproof glass... But if you can get a wireless access point and get it at the entrance of the basement, it will take the signal from your router and extend it into your basement. You can take these WAPoints and move them around to see where you get the best signal in your basement with where the access point extends the signal too. I hope this helps. Also some of the other items listed above can cause inteference but I would suspect the concrete and start there. There not too expensive and you can have more than one.
Powered by Yahoo! Answers
Title Post: Hot to set up a sound system throughout the house?
Rating: 96% based on 987 ratings. 4,3 user reviews.
Author: Unknown
Thanks For Coming To My Blog
Rating: 96% based on 987 ratings. 4,3 user reviews.
Author: Unknown
Thanks For Coming To My Blog
No comments:
Post a Comment